Home > Not Working > Bathroom Light Not Working

Bathroom Light Not Working

Contents

The best way to solve the problem is to set the fan on “hi” using the wall switch. Now.. When I push the buttons on the remote, nothing happens, or the fan turns slowly. All times are GMT -4. check over here

Any suggestions? I checked the wire from the main breaker to on of the washroom plug its look like disconnected from somewhere but the wire between the both washrooms is connected also I Dave's Reply: Thanks for your electric wiring questions Ingrid, Beki and Jim. Should I be worried?Before you worry, find a small table lamp and plug it into the outlet in question. http://ask-the-electrician.com/why-is-my-bathroom-light-fixture-not-working/

Bathroom Light Not Working

Undo randy427 My first guess would be that moisture collecting in the fan housing is causing the GFCI to trip. Bad breaker in the panel 4. If turning off the master breaker (or all other breakers) eliminates the hum, then turn them on one at a time until you find the one that turns the hum back See Sample Yard + Garden Twice-monthly advice for bringing your home outdoors, from year-round yard upkeep and planning to the wonders of making your garden grow, plus special offers.

Any ideas, and I am not electrical inclined. If the GFCI breaker resets OK then see if the bathroom light fixture is working. Once the operating speed is reached, the vacuum consumes less energy and does not cause the lights to dim.A home inspector noticed that my home has some light fixtures wired with Bathroom Light Not Working Bulb Ok The electrical outlet works as I plugged my electric shaver in and it does work.

Loose or faulty wiring connections may be the cause of this problem, however some electrical troubleshooting will be necessary. NOTE: Electrical problems like this are best discovered when using a voltage tester. The combination of lights tells what kind of circuit you have.

The Key Cost Factors for Bathroom Remodel Electrical Wiring.

Hauppauge, NY 11788. Bathroom Light Wont Turn On I opened it up and tried to pull the black wire and it made sparks. A practical example of a controlled short circuit is the spark generated by an arc welder. I checked all GFI plugs and check the breakers and all are in working condition.

Bathroom Light And Fan Not Working

Undo hexus "your problem was created by the installer." I disagree, there is no way for you to tell that it was the installer's fault. http://www.handymanusa.com/questions/electricaltroubleq.html Tell your friends about this page! Bathroom Light Not Working Randy427-This has happened intermittenly ever since the install. Lights Wont Turn On Breaker Not Tripped Thanks so much!

Also, the radio gets staticky at the same time. http://noipc.org/not-working/macbook-charger-not-working-no-light.html It is just a circuit connection box where the individual circuits are connected, with circuit protectors (breakers) in line before it connects to the main line to your electric usage meter. Dave Rongey says: December 4, 2012 at 4:03 am Hi Don, I suspect there is a problem with the circuit wiring, and the problem may be found at a connection or I have eliminated all of the thermal switches on each unit, except for one (1), as a safety precaution. Bathroom Light Not Working But Fan Is

Repaired that and it worked for a while again. So.. If the switch does have power then turn it on - is there power to the other terminal? http://noipc.org/not-working/wd-passport-light-on-but-not-working.html Could this be the fuse.

Is there a short causing this problem?A short circuit is a potential problem for a light pole. No Power In Bathroom Breaker Not Tripped Consult a licensed electrician who is qualified to evaluate the problem.I have a refrigerator in my basement or garage that does not work, or the GFCI receptacle that it is plugged Another answer: I bought a simple 3prong tester at a hardware store for just a few dollars.

All Rights Reserved.|Membership Agreement Terms of Use | Privacy Policy (703) 494-3989  TOUCH TO CALL! (703) 494-3989 HOME ABOUT RESIDENTIAL Residential Electric Services Electric Panel Change Electric Sub Panel Installation

Wiring GFI Outlets GFCI and GFI Wiring Diagrams The features and benefits of GFCI outlets and receptacles will give you a clear understanding of the importance why these safety devices are It is essentially a transformer that converts the voltage from 120 volts to whatever the fluorescent bulb needs to run. Lights not working in one of those bathrooms. Bathroom Fan Works But Light Doesn't If you replace any outlets, use the screws on the outlets to secure the leads.

some US jurisdictions require the stove frame connected to neutral). After installation, using a ground tester, three of the outlets showed a green light on the tester (meaning connections OK). The power is going from your on/off switch to the light, then from the light to the fan, right? have a peek at these guys It's really works well.

Precaution: Identify the project circuit, turn it OFF and Tag it with a Note before working with the wiring. The ballast in a fluorescent light fixture is the black box on the inside of the fixture. A bulb blew out. Perfect!"The one exception is that outlets intended for motor-driven appliances, like washers and driers, don't need a GFCI, as GFCIs don't work with inductive loads."

But the new

I shut off the power, waited and then turned it back on. Hakkında Basın Telif hakkı İçerik Oluşturucular Reklam Verme Geliştiriciler +YouTube Şartlar Gizlilik Politika ve Güvenlik Geri bildirim gönder Yeni bir şeyler deneyin! If you have one switch that controls two heat lamps there may be a potential load of 500 watts just for that individual switch, and that will definitely stress the switch Turned them all off and on again with no improvement.

find the neutral that isn't connected correctly. Sometimes an outlet in another room is wired on the same circuit, especially in older homes, and a tripped GFCI in your bathroom is shutting it off. Sometimes it sticks somewhere in the middle; sometimes it sticks so close to on that it's hard to see it's tripped. Thanks, Allan Dave Rongey says: September 6, 2010 at 5:06 pm Birdie, It sounds like the switch for the light is bad and needs to be replaced.

Bulbs Burn Out Every Few Days I have a ceiling light where lightbulbs are burning out every few days. What is also weird is that sometimes these plugs work, but most of the time they don't? What could cause an outlet to stop working like that for a very small amount of time and then start working again? Now plug in your circuit tester.

The other bath's normal outlet was tied to the GFCI in the first bath. The 4 fuses for these two outlets are housed in 2 devices that I am unfamiliar with. I try the same light bulb in the other bathroom and it work. Thanks Dave AL Dave Rongey says: July 9, 2012 at 7:11 am Thanks very much Brian, The GFI in the garage normally does not feed power into the bathrooms, but still

The 15 and 20 amp circuit breakers should be double checked to see if one is tripped, but may appear to be in the ON position. WHAT YOU NEED FOR THIS PROJECT Phillips head screwdriver Slotted screwdriver Wire stripper Voltage tester Flashlight GFCI outlet TOOLS Phillips head screwdriver Slotted screwdriver Wire stripper Voltage tester Flashlight MATERIALS GFCI If they are, reset the circuit breaker.