Home > Not Working > Gauges Not Working On Dashboard

Gauges Not Working On Dashboard

Contents

I was told by a mechanic a few months ago that it was a sensor on the motor. Just for giggles…. Tried a new head light switch still blows the fuse. I think your problem would be more drivability in the fuel (fuel pump injectors fuel lines)... Source

Thank you, Stu 267-225-2191 Reply April 27, 2014 at 7:06 am ruth I have a 1993 Camaro and some of the light work on it .when i get ready to make Reply September 22, 2014 at 2:30 pm Stuart Gross It's a simple cluster repair… contact your local speedometer repair shop. Something is causing it to burn out Reply April 12, 2014 at 7:07 pm Stuart Gross Hi, It's time to have the car diagnosed by a specialist, since you replaced the Instead, tilt the cluster forward and reach behind it to disconnect the wiring clip and speedometer wire if your vehicle has one. [8] Older model vehicles will have a separate cable

Gauges Not Working On Dashboard

All of the lights in the cluster are working. Thanks, Stu 267-225-2191 Reply July 8, 2014 at 1:34 pm Stephanie I have a 2001 Sebring and my instrument cluster doesn't light up at night so I can't see what speed Loading... I've even changed the instrument cluster and the BCM.

Reply December 4, 2014 at 8:13 pm Stuart Gross You have serious issues. wikiHow Contributor Well, if you have to pull on a knob to turn your lights on, try twisting the knob in both directions because in my truck you can control the Home Categories FAQ/Guidelines Terms of Service Privacy Policy Powered by Discourse, best viewed with JavaScript enabled CarTalk.com Blogs Car Info Our Show Mechanics Files Skip navigation UploadSign inSearch Loading... Dashboard Gauges Not Working Problems Now it's off about 10 miles.

Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Have it checked by a trained professional. You can only upload a photo or a video. click resources Ammeter Gauge - Turn headlights ON (do not start engine).

When you get to a gauge that you have removed the feed from and the problem goes away, you have found the culprit. Instrument Cluster Gauges Not Working No turn signals, odometer, tach, speedometer, temperature or fuel. Pull the dimmer switch and the cluster backing lights that illuminate in the night don't turn on. Insert a new fuse into the slot you removed the old one from.

Dashboard Gauges Dont Work

Thanks, Stu Reply November 5, 2014 at 7:02 pm John I have a 2004 chevy blazer and when I turn my car off after driving the gas and oil gage move Bad connection in the back of the cluster? Gauges Not Working On Dashboard im going to jump it off my moms car when she gets home. Car Gauges Stop Working While Driving only the trip milage resets not the actual milage..

Idle the engine briefly. this contact form Although my background is in auto sales, I’ve found my passion by providing reasonably priced solutions to car owners for items usually purchased at dealerships. Add to Want to watch this again later? Shop Home Find a Dealer News & Updates Tech Help About Us Contact Us Copyright 2016 American Autowire, Inc. None Of My Gauges Work On My Dashboard

Once the new instrument cluster is working, replace all of the pieces of the dashboard you removed to access it. Maybe there is a BMW expert with some experience with this, if not on this site, but online. Transcript The interactive transcript could not be loaded. have a peek here ok, this is a power control module communication problem and some times it can be fix by disconnecting the negative side of the battery and reconnecting after 3 minutes.

Defective gauge Magnetic gauge: Disconnect the wire at the sending unit. Gauge Cluster Lights Not Working do I need a new instrument cluster? Source(s): gauges stop working car: https://shortly.im/SMHKe Sorcha · 1 year ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Report Abuse Most likely fuse.

Owned it 17 hrs and the computer had to be replaced.

A few weeks later no power windows on pass side then they would work. With ignition on, gauge should register COLD. Read more P2428 OBD-II Trouble Code: Exhaust Gas Temperature Too High Bank 1 P2428 code definition A P2428 trouble code signifies that the PCM has detected a problem in the exhaust My Instrument Panel Is Not Working Thank you, Stu Reply October 1, 2014 at 9:48 am Shelby Mellinger I have a 94 dodge ram and just a couple of days ago i was driving and ever single

Part 2 Replacing Dashboard Light Bulbs 1 Disconnect the battery. I have a 2003 Nissan Maxima GLE (Fifth Generation), and when some of my lights in my cluster panel is working (Only one side). I have already replaced the fuse. Check This Out Required fields are marked *CommentYou may use these HTML tags and attributes:

Instrument cluster doesn't work (ie. consider the dealer as well… Thank you, Stu Reply July 30, 2014 at 2:34 pm DB 2006 infiniti qx56 - rpm not working, some of the dash lights not lit, when Show more unanswered questions Ask a Question Submit Already answered Not a question Bad question Other If this question (or a similar one) is answered twice in this section, please click Thank you, Stu Reply October 21, 2014 at 11:41 pm Dakota Hey I have a 2003 pontiac grand am.

If not, check the “gauges” fuse at the panel. Thanks, Stu Reply July 21, 2014 at 5:52 pm Ameek Hi, I have an 03 Infiniti I35 & my check engine light is on. Thank you, Stu Reply November 4, 2014 at 4:58 am Chad 99 GMC Suburban K1500 4×4 While using 4WD offroad and muddy, certain gear selector lights started to flicker. oh ya, and now when the car is running (like driving down the road) if i turn the head lights on, there is a non stop dinging sound, like if the

If they are working but your dashboard doesn't report that they are working, and if the fuses are all okay, then there is a design flaw going on. Am I going nuts are could these two things actually be related? prolly not....but maybe..? Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...

Ground the wire, gauge should register HOT. See it in Louisville next week @ the Street Rod Nats! #HRIApinewoodbuilderschallenge https://t.co/9PrYlIrlqV Come see us and our newest products in Columbus! #goodguyscolumbus https://t.co/K8aLPV02jh Our 1968-70 Mopar B Body kit is If they are ok then the trouble may be with a loose connector to the dash panel. thanks for ur help.

It happened for a day or two about a month ago and then stopped. Make sure all of the connections are in the same place and that the dash board conveys the same information that the original did.[11] Make sure the speedometer lists miles per Reply December 6, 2014 at 7:51 pm Stuart Gross typical issue with GM clusters…. Why is my car making a rattling sound?

Remove the wire harness plug, inspect, clean and make sure the connection is secure. Check all the connections @ the transmission. What should I do?