Home > Water Heater > My Water Heater Is Not Heating Water

My Water Heater Is Not Heating Water

Contents

Thanks for listening. Read and follow the temperature adjustment instructions and safety notices in the Installation Manual that came with your new water heater. I was out of town and just returned today. If line voltage is present on a heating element, it must heat the water unless the element has failed. 44 Return all thermostats to an equal value of your choosing, but http://noipc.org/water-heater/rinnai-tankless-water-heater-troubleshooting-no-hot-water.html

It is important that all gasket material, filings, rust etc., be completely removed to reveal as smooth a surface as possible. Use the multimeter's voltage and resistance functions to help narrow down to the defective device. Sequence of Operation of Electric Water Heater Elements Most electric water heaters are what we call "flip flop" or "non-simultaneous" electric water heater systems, meaning that just one of the two Check for power at fuse or circuit breaker. http://www.whirlpoolwaterheaters.com/owner-center/installation-video-guides/electric-installation-videos-guides/troubleshooting-repair/

My Water Heater Is Not Heating Water

Some have specific jacks to connect probes for particular measurements, while others use two jacks for all measurement types. The hot water heater is only about 2 years old. Reconnect the wires, making sure the connections are tight.

Do not over tighten. 12 Make sure the nearest hot water faucet is still open and begin filling the water heater by opening the cold water supply valve. An Amprobe clamp on ammeter indicates a 15.9 amp heating element load. It is also possible that the water heater is too small or that your usage has increased. "Water Drips" Water Leaks With a new water heater, most leaks are caused by Gas Water Heater Not Working The Illustrated Home illustrates construction details and building components, a reference for owners & inspectors [3] Thanks to reader Red Wood for clarification about the operation of electric water heater elements.

If the fuse blows again or the circuit breaker trips again, do not re-fuse or re-set the breaker as the system is unsafe and you need a professional electrician. Electric Water Heater Reset Button Carson Dunlop Associates' provides extensive home inspection education and report writing material.The Illustrated Home illustrates construction details and building components, a reference for owners & inspectors. Heating elements are held to the water heater either with a large thread and nut as shown here or by four bolts and nuts. http://www.water-heater-repair-guide.com/electricwaterheatertroubleshooting.html The Home Reference Book - the Encyclopedia of Homes, Carson Dunlop & Associates, Toronto, Ontario, 25th Ed., 2012, is a bound volume of more than 450 illustrated pages that assist home

Do make sure the fitting is quite clean before putting in the new element. Electric Hot Water Heater Not Working After Power Outage Published on Oct 4, 2013A very nice video tutorial on how you can easily identify the cause of an electric water heater failure. it will be best to tighten these bolts the way lug nuts on a tire are tightened - one nut, then the opposite nut, repeat as needed. If the meter being used does not provide for range selection, it is likely an "autoranging" type.

Electric Water Heater Reset Button

Smith, "Residential Gas & Electric Water Heatern Service Handbook", A.O. http://www.whirlpoolwaterheaters.com/owner-center/installation-video-guides/electric-installation-videos-guides/troubleshooting-repair/ I put in both heating elements and the upper thermostat and still cant get hot water what's should i do next - Earl Baker 2/19/2013 i have replaced both elements @ My Water Heater Is Not Heating Water If the pressure is higher than that, install a Pressure Regulating Valve (or adjust your existing pressure regulating valve if you have one). How To Tell If Electric Water Heater Is Working If the meter displays a value other than a very high value (millions of ohms), preferably infinity, the element should be replaced, described later. 21Reconnect the wire that was removed from

This operation continues until the water in both halves of the tank is equal to the settings of their respective thermostats. this contact form While this was happening, the water heater knocked a few times. The curcuit wasnt tripped, and I couldnt figure the problem. electronicsNmore 3,102 viewsNew 22:59 Loading more suggestions... Electric Water Heater Thermostat

Cold water will enter the bottom of the tank and mix with the existing hot water in the tank, lowering the overall temperature. 35If line voltage not found at the element I have an 80 solar water tank with electric backup, mixing valve, upper heating element only, PT valve and solar panels upper manifold air release valve. Both amp measurements should be pretty close to equal (within 10 % or so). have a peek here Do make sure the fitting is quite clean before putting in the new element.

See TIMERS for ELECTRIC WATER HEATERS. How To Test Water Heater Element Add a photo Upload error Article Info Featured Article Categories: Featured Articles | Water Heating Systems In other languages: Português:Reparar um Aquecedor de Água Elétrico,Русский:отремонтировать водонагреватель,Italiano:Riparare uno Scaldabagno Elettrico,Español:reparar un calentador Of course life is more complicated.

Check first one screw, then the other.

These unintended paths can be dangerous and make troubleshooting very difficult to perform. HomeOwnerRepair 240,413 views 2:07 WATER HEATER ELEMENT- how to TEST - Duration: 3:12. Plumbing Repair: DIY Tips and Step-By-Step Guides Water Heater Tutorials How to Troubleshoot and Repair an Electric Water Heater By Bob Formisano Home Repair Expert Share Pin Tweet Submit Stumble Post Not Enough Hot Water From Electric Water Heater The leaking water likely caused a thermostat to malfunction too.

I had hot water and everything was cool, until today (I hate cold showers before work). If the elements are not shorted and there are no other electrical problems you can find, I'd replace the thermostat unit. Because the first element I removed was rated 4500 watts, I replaced it with a basic cheap 4500-watt one. http://noipc.org/water-heater/gas-water-heater-thermocouple.html Continue reading at ELECTRIC WATER HEATER ELEMENT TESTS or select a topic from the More Reading links or topic ARTICLE INDEX shown below.

Any chance you tested with a 20 amp fuse by mistake? (Somebody help out - any chance those element draw a lot until the get hot? Replace the insulation and metal covers. You might also enjoy: Sign up There was an error. Sooty, black carbon deposits on surfaces indicate a short circuit.

This guide is electric water heater specific. Excessive buildup of sediment in bottom of tank is causing overheating of tank bottom and boiling of water to occur. Possible RepairsRemove sediment by flushing water heater. 8 of 9 Show All It may help to bring along the old controls for comparison to the new controls. 6 Clean the tank surface that the controls contact. Any idea where I can find a better thermostat that will fit?

More on this, later. 31After attempting reset, check the heating element for power again. 32If still no power present, test the top left and right terminals of the high temp switch Since the expanded water now has nowhere to go, the water pressure in the house's pipes can increase dramatically, often to the point where the Temperature and Pressure Relief Valve discharge If power is still on, do not proceed until you locate the fuse or circuit breaker supplying power. Carson, Dunlop & Associates Ltd., 120 Carlton Street Suite 407, Toronto ON M5A 4K2.

Possibly the upper one overheated if it was exposed to that air. The digital meter should indicate a "low" value very close to zero.